Page 2 of 3
Re: XTinyTerror.lv2
Posted: Sat Apr 18, 2020 3:47 am
by tramp
@tavasti
damn. The repository was still on the wrong submodule checkout from libxputty. It's fixed now finally.
Please update your checkout.
Re: XDarkTerror.lv2
Posted: Sun Apr 19, 2020 1:34 pm
by tramp
funkmuscle wrote: ↑Thu Apr 16, 2020 7:17 pm
Is there a Black TinyTerror? The heavier sounding Orange amp?
Here it is:
Like with the TinyTerror, use it with a cabinet simulation or IR for best results, as it is the plain head simulation. It sound very harsh without a following cabinet.
https://github.com/brummer10/XDarkTerror.lv2
Re: XDarkTerror.lv2
Posted: Sun Apr 19, 2020 3:23 pm
by funkmuscle
tramp wrote: ↑Sun Apr 19, 2020 1:34 pm
funkmuscle wrote: ↑Thu Apr 16, 2020 7:17 pm
Is there a Black TinyTerror? The heavier sounding Orange amp?
Here it is:
Like with the TinyTerror, use it with a cabinet simulation or IR for best results, as it is the plain head simulation. It sound very harsh without a following cabinet.
https://github.com/brummer10/XDarkTerror.lv2
yessir, you did it again!!! Thank bro!
Re: XTinyTerror.lv2
Posted: Tue Apr 21, 2020 11:59 am
by carlv
Howdy
XTinyTerror is working fine, but XDarkTerror starts out ok , then starts to sizzle and eventually fizzles out. Hitting the on/off switch re-sets, but then it happens again within a few seconds.
Re: XTinyTerror.lv2
Posted: Tue Apr 21, 2020 12:40 pm
by tramp
carlv wrote: ↑Tue Apr 21, 2020 11:59 am
XTinyTerror is working fine, but XDarkTerror starts out ok , then starts to sizzle and eventually fizzles out. Hitting the on/off switch re-sets, but then it happens again within a few seconds.
Which sample rate do you use?
Side note, I expected such a report already, and have a idea at hand how to fix it.
Currently XDarkTerror use a 4x oversampling to avoid artefacts from the clipping. XTinyTerror didn't need oversampling.
That work well with a sample rate of 48kHz.
It will be properly wiser to use a fixed sample-rate internal so that the filters cant stoke up.
Re: XTinyTerror.lv2
Posted: Tue Apr 21, 2020 1:07 pm
by carlv
tramp wrote: ↑Tue Apr 21, 2020 12:40 pm
That work well with a sample rate of 48kHz.
It will be properly wiser to use a fixed sample-rate internal so that the filters cant stoke up.
More than likely that's the case here. I use 48khz only on rare occasions. It's pretty much overkill for my meagre needs. Thanks for the heads up.
Re: XTinyTerror.lv2
Posted: Tue Apr 21, 2020 5:25 pm
by tramp
So I've pushed a fix for XDarkTerror to use a fixed sample rate internal (192kHz). This is enough for avoiding artefacts from the distortion routine, and the filters will be run stable.
@carlv thanks for reporting the issue.
Re: XTinyTerror.lv2
Posted: Tue Apr 21, 2020 6:01 pm
by carlv
Buttery success !
As always, thank you much..
Re: XTinyTerror.lv2
Posted: Wed Apr 22, 2020 9:24 am
by tavasti
tramp wrote: ↑Sat Apr 18, 2020 3:47 am
@tavasti
damn. The repository was still on the wrong submodule checkout from libxputty. It's fixed now finally.
Please update your checkout.
Did:
Code: Select all
make clean
git pull
make
sudo make install
And still, when plugin active and opening it for adjusting sound, and then close -> crash
Re: XTinyTerror.lv2
Posted: Wed Apr 22, 2020 9:55 am
by tramp
tavasti wrote: ↑Wed Apr 22, 2020 9:24 am
And still, when plugin active and opening it for adjusting sound, and then close -> crash
mm, that means that the submodule didn't update.
You may do a make clean again and then do a
if that didn't work, please delete your copy and do a fresh clone.
Re: XTinyTerror.lv2
Posted: Wed Apr 22, 2020 10:55 am
by tavasti
tramp wrote: ↑Wed Apr 22, 2020 9:55 am
tavasti wrote: ↑Wed Apr 22, 2020 9:24 am
And still, when plugin active and opening it for adjusting sound, and then close -> crash
mm, that means that the submodule didn't update.
You may do a make clean again and then do a
Yeah, that fixed a thing. I am not familiar with submodules, so did not understand that it needs separate update.
Thanks!
Re: XTinyTerror.lv2
Posted: Thu Apr 23, 2020 2:11 am
by tseaver
@tavasti said:
I am not familiar with submodules, so did not understand that it needs separate update.
I'm a professional software developer, and have been using git for more than a decade now, and I *still* screw up submodules routinely (I never use them in my own projects, so my mental model for them is b0rken).
Re: XTinyTerror.lv2
Posted: Thu Apr 23, 2020 5:09 am
by tramp
I've developed libxputty to serve as GUI toolkit for my LV2 plugins. Using it as submodule allow me to maintain the source base of the toolkit in a central place instead as part of any single plugin. This reduce boilerplate code and maintenance work.
This is relative new, TinyTerror is the first plug which use the lv2_plugin base integrated in libxputty.
Any report helps to make this easier to handle. I may include a routine in the makefile which check if the submodule needs a update.
Re: XTinyTerror.lv2
Posted: Thu Apr 23, 2020 10:28 am
by tramp
tramp wrote: ↑Thu Apr 23, 2020 5:09 am
I may include a routine in the makefile which check if the submodule needs a update.
. . . and done, the makefile will keep track now for needed submodule updates.
Re: XTinyTerror.lv2
Posted: Thu Apr 23, 2020 10:37 am
by tavasti
tavasti wrote: ↑Fri Apr 17, 2020 4:11 pm
From your amps, what is most 'metal' amp? Modern metal amp is what I would need.
@tramp, do you have cure for this itch?