Page 2 of 2
Re: Run RME Digi96/8 pad in Kxstudio
Posted: Sun Mar 09, 2014 5:02 pm
by Snap
Found how to blacklist a sound card and now the Intel card is out of the way, but the Digi96 still not working. rmedigicontrol still not founding the card.
I've got these outputs:
Code: Select all
aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: R15 [RME Digi9652 (Rev 1.5)], device 0: RME Digi9652 (Rev 1.5) [RME Digi9652 (Rev 1.5)]
Subdevices: 1/1
Subdevice #0: subdevice #0
Code: Select all
lspci |grep RME
04:00.0 Multimedia audio controller: Xilinx Corporation RME Digi9652 (Hammerfall) (rev 03)
Code: Select all
cat /proc/asound/cards
0 [R15 ]: RME9652 - RME Digi9652 (Rev 1.5)
RME Digi9652 (Rev 1.5) at 0xfd000000, irq 19
Code: Select all
cat /proc/asound/modules
0 snd_rme9652
Code: Select all
cat /proc/asound/R15/rme9652
RME Digi9652 (Rev 1.5) (Card #1)
Buffers: capture ffff880037200000 playback ffff880036c00000
IRQ: 19 Registers bus: 0xfd000000 VM: 0xffffc90000646000
Control register: 24500c
Latency: 4096 samples (2 periods of 16384 bytes)
Hardware pointer (frames): 0
Passthru: no
Clock mode: autosync
Pref. sync source: ADAT1
ADAT1 Input source: ADAT1 optical
IEC958 input: Coaxial
IEC958 output: Coaxial & ADAT1
IEC958 quality: Consumer
IEC958 emphasis: off
IEC958 Dolby: off
IEC958 sample rate: undetermined
ADAT Sample rate: 44100Hz
ADAT1: No Lock
ADAT2: No Lock
ADAT3: No Lock
Timecode signal: no
Punch Status:
1: off 2: off 3: off 4: off 5: off 6: off 7: off 8: off
9: off 10: off 11: off 12: off 13: off 14: off 15: off 16: off
17: off 18: off 19: off 20: off 21: off 22: off 23: off 24: off
25: off 26: off
Notice this:
IEC958 sample rate: undetermined
Re: Run RME Digi96/8 pad in Kxstudio
Posted: Sun Mar 09, 2014 5:06 pm
by Snap
I run
and the dbx Quantum gets effectively synched via S/PDIF @ 44.1 KHz. Isn't it weird?
Of course, no sound at all.
Re: Run RME Digi96/8 pad in Kxstudio
Posted: Sun Mar 09, 2014 5:31 pm
by Snap
gnome-alsamixer reports this error when opening:
Bad key or directory name: "/apps/gnome-alsamixer/display_mixers/": Key/directory may not end with a slash '/'
Bad key or directory name: "/apps/gnome-alsamixer/display_names/": Key/directory may not end with a slash '/'
But cannot find any of those two directories within my system.
Re: Run RME Digi96/8 pad in Kxstudio
Posted: Sun Mar 09, 2014 7:04 pm
by stanlea
So you're on progress...
Idon't think you should use RMEdigicontrol, but instead HDSPconf and HDSP mixer. They should be installed in your system.
Re: Run RME Digi96/8 pad in Kxstudio
Posted: Mon Mar 10, 2014 9:13 am
by Snap
Really? For the Digi96? I always read the Digis should be used with the rmedigicontrol instead. AFAIK, the HDSPconf is intended for the later hdsp cards...
I'll try anyway.
Re: Run RME Digi96/8 pad in Kxstudio
Posted: Mon Mar 10, 2014 9:23 am
by Snap
No luck.
Code: Select all
hdspconf
HDSPConf 1.4 - Copyright (C) 2003 Thomas Charbonnel <thomas@undata.org>
This program comes WITH ABSOLUTELY NO WARRANTY
HDSPConf is free software, see the file copying for details
Looking for HDSP cards :
Card 0 : RME Digi9652 (Rev 1.5) at 0xfd000000, irq 19
Card 1 : HDA Intel at 0xf9ffc000 irq 43
No Hammerfall DSP card found.
Re: Run RME Digi96/8 pad in Kxstudio
Posted: Tue Mar 11, 2014 11:53 am
by Snap
I give up. I have the impression that the card is faulty. Don't have a windows system on hand at this moment to check it, but tried two different computers and a bunch of different Linux distros and the same problem happens every time.
IEC958 sample rate: undetermined
I never seen anyone else having this issue whether the card works fine or is not recognized.
Going for a second hand HDSP9652. Case closed.
Re: Run RME Digi96/8 pad in Kxstudio
Posted: Wed Mar 12, 2014 9:04 pm
by stanlea
I think you should not give up. Google around and you'll see that this card is not recognized by REMdigicontrol and the HDSPware, but some people semm to have success, given some manual settings. Maybe you should ask Paul Davis directly, he is the maintener for the alsa driver. He's the main developer of Ardour, so he's not hard to join.