Page 4 of 5
Re: Triceratops and SynthV1 in KXStudio
Posted: Mon Jan 07, 2013 5:24 pm
by briandc
IIRC, I used "alien" and "fakeroot" to install Synthv1 on my Bodhilinux PC, since the package on sourceforge is .rpm and not .deb.
I suppose I can do the same thing on KXStudio, right? On Bodhi Synthv1 seems to be working just fine... it even installed into the menu bar!
Any thoughts? Do you guys use fakeroot/alien for anything on your PCs?
brian
Re: Triceratops and SynthV1 in KXStudio
Posted: Mon Jan 07, 2013 5:29 pm
by autostatic
There are synthv1 packages available in the KXStudio plugins repository. I would use those and not an rpm that is build for OpenSuSE.
Re: Triceratops and SynthV1 in KXStudio
Posted: Mon Jan 07, 2013 6:24 pm
by briandc
AutoStatic wrote:There are synthv1 packages available in the KXStudio plugins repository. I would use those and not an rpm that is build for OpenSuSE.
Yes, but I installed, removed and reinstalled with no luck..
brian
Re: Triceratops and SynthV1 in KXStudio
Posted: Tue Jan 08, 2013 10:32 pm
by briandc
Well, good news! I had to "sudo rm -r" some additional synthv1 files I found in various places. Then I did an updatedb and reinstalled synthv1.
It works! Yea! I can even save patches!
Now I can also go to bed..
Just waiting now for the new release of Triceratops so I can make a bank or two of patches there, too!
brian
PS. Falk, was the update for Phasex not possible?
Re: Triceratops and SynthV1 in KXStudio
Posted: Wed Jan 09, 2013 9:10 am
by briandc
falkTX wrote:briandc wrote:PS. Falk, was the update for Phasex not possible?
I assume it is, haven't checked yet.
I'll do that tomorrow.
Which reminds me, we need a better way to deal with package requests... any suggestions?
Depends on what is important. Maybe a dedicated thread?
brian
Re: Triceratops and SynthV1 in KXStudio
Posted: Mon Jun 17, 2013 6:32 pm
by briandc
- shot-2013-06-17_20-31-13.png (88.99 KiB) Viewed 1445 times
Hi everyone,
I'm a bit confused about the newest release of Triceratops. I downloaded the package (older PC using Bodhi Linux) and unzipped it. Read the ReadMe and ran the commands to build. But the second command failed, it seems I must be missing a whole lot of libraries... correct?
The image above gives the output of the failed command ./waf.
BTW, it looks like Triceratops is to be run using galv.gtk... --Is Triceratops is a type of SAS? (software as service?)
Any feedback much appreciated by this apprentice!
brian
Re: Triceratops and SynthV1 in KXStudio
Posted: Tue Jun 18, 2013 6:21 am
by briandc
falkTX wrote:triceratops is already the latest version afaik.
anyway, if you want to recompile any software in the kxstudio repos, the deps can be easily installed with for example:
Code: Select all
sudo apt-get build-dep triceratops-lv2
Yes, on KXStudio I'm sure it is. I was doing an install on another pc that doesn't have KXstudio that gave me the errors. I just wanted to know if the errors were due to missing packages.
brian
Re: Triceratops and SynthV1 in KXStudio
Posted: Tue Jun 18, 2013 1:22 pm
by StudioDave
briandc wrote:... I just wanted to know if the errors were due to missing packages.
The compiler's error report indicates an outdated or broken installation of the LV2 package. You're missing an extension with the state.h header.
Best,
dp
Re: Triceratops and SynthV1 in KXStudio
Posted: Tue Jun 18, 2013 5:08 pm
by briandc
StudioDave wrote:briandc wrote:... I just wanted to know if the errors were due to missing packages.
The compiler's error report indicates an outdated or broken installation of the LV2 package. You're missing an extension with the state.h header.
Best,
dp
hi dp and thanks for responding.
is the outdated package in the triceratops package or somewhere else? should i ask the guys at bodhi to update something?
brian
Re: Triceratops and SynthV1 in KXStudio
Posted: Tue Jun 18, 2013 7:22 pm
by StudioDave
briandc wrote:StudioDave wrote:
The compiler's error report indicates an outdated or broken installation of the LV2 package. You're missing an extension with the state.h header.
is the outdated package in the triceratops package or somewhere else? should i ask the guys at bodhi to update something?
It's the LV2 library package itself. Do this to verify :
On my KXStudio box it returns this information :
dlphilp@Maximus-i386:~$ lv2config | grep state
/usr/include/lv2/lv2plug.in/ns/ext/state => /usr/lib/lv2/state.lv2/
Also :
dlphilp@Maximus-i386:~$ ls -l /usr/include/lv2/lv2plug.in/ns/ext/state/
-rw-r--r-- 1 root root 1507 Feb 23 10:19 lv2-state.doap.ttl
-rw-r--r-- 1 root root 233 Feb 23 10:19 manifest.ttl
-rw-r--r-- 1 root root 14581 Feb 3 08:33 state.h
-rw-r--r-- 1 root root 12837 Feb 3 08:33 state.ttl
Let me know what your system reports.
Best,
dp
Re: Triceratops and SynthV1 in KXStudio
Posted: Wed Jun 19, 2013 7:58 am
by briandc
Hi dp,
I only get a "lv2config: command not found".
brian
Re: Triceratops and SynthV1 in KXStudio
Posted: Wed Jun 19, 2013 8:44 am
by briandc
falkTX wrote:You should remove lv2core and install lv2-dev instead.
Hi falk,
I removed lv2core.
Is the lv2-dev package you refer to one of these:
libnabrit-dev
liblilv-dev
libnacore5
libnacore-dev
libpaq-dev
libnabrit2
libslv2-dev
lv2-c++-tools
libnabrit-dbg
liblv2dynparam1-dev
..?
thx..
brian
Re: Triceratops and SynthV1 in KXStudio
Posted: Wed Jun 19, 2013 9:06 am
by briandc
falkTX wrote:no, it's really "lv2-dev".
The package has been in the KXStudio repos for quite some time now...
If you don't have that package then you can't build any new-ish lv2 software.
Got it. However, I'm using Bodhi linux on this pc (not my usual pc for music). If I can add the KXStudio repos that might be cool. Will that work? (it's debian-based)
brian
Re: Triceratops and SynthV1 in KXStudio
Posted: Wed Jun 19, 2013 10:45 am
by briandc
falkTX wrote:briandc wrote:Got it. However, I'm using Bodhi linux on this pc (not my usual pc for music). If I can add the KXStudio repos that might be cool. Will that work? (it's debian-based)
It will only work if it's Ubuntu based (for now).
Looks like it's Ubuntu-based after all:
http://www.bodhilinux.com/about_bodhi.php
So I just insert the repos that are listed on kxstudio.sourceforge.net, right? Which in particular will I need for the LV2 problem?
brian
Re: Triceratops and SynthV1 in KXStudio
Posted: Wed Jun 19, 2013 12:01 pm
by briandc
falkTX wrote:
Depends on the base Ubuntu version.
12.04 is fine and supported, older ones will not work, and new ones will kinda work but I don't run them to confirm how well they do.
Good news.. I added the base and plugin repositories, and installed the lv2-dev file: I was able to install Triceratops correctly! Yeah!
It runs in Qtractor fine, but not with jalv.gtk.. I got:
Code: Select all
Missing feature urid:map. Segmentation fault.
brian