qjackctl with "JACK Bridges"
Moderators: MattKingUSA, khz
- khz
- Established Member
- Posts: 1648
- Joined: Thu Apr 17, 2008 6:29 am
- Location: German
- Has thanked: 42 times
- Been thanked: 92 times
qjackctl with "JACK Bridges"
rncbc: Would a "JACK Bridges" setting option be possible in qjackctl? Similar to https://kxstudio.linuxaudio.org/Applications:Cadence.
. . . FZ - Does humor belongs in Music?
. . GNU/LINUX@AUDIO ~ /Wiki $ Howto.Info && GNU/Linux Debian installing >> Linux Audio Workstation LAW
. . GNU/LINUX@AUDIO ~ /Wiki $ Howto.Info && GNU/Linux Debian installing >> Linux Audio Workstation LAW
- I don't care about the freedom of speech because I have nothing to say.
- nikgnomicradio
- Established Member
- Posts: 109
- Joined: Wed Feb 07, 2018 9:31 pm
- Has thanked: 1 time
- Been thanked: 7 times
- Contact:
Re: qjackctl with "JACK Bridges"
Pulseaudio to JACK bridge on Cadence is redundant
If Pulseaudio is correctly configured with module-jackdbus-detect, Pulseaudio JACK Sink/Source connections are automatically loaded when JACK starts
I have seen a few Cadence users turn on the Pulseaudio bridge option without noticing that connections are already loaded and create a second pair of Pulseaudio connections
in QjackCtl just need to turn on 2 settings to use D-Bus, Pulseaudio JACK Sink/Source connections are automatically loaded
if using D-Bus is not possible or preferable, Pulseaudio sinks and sources can be loaded by simple terminal commands
This can be configured to run automatically in QjackCtl using option to run script after JACK started
QjackCtl option to run script after JACK started can also be used for connections to ALSA loopbacks
Not recommended to run both ALSA and Pulseaudio connections
If Pulseaudio is correctly configured with module-jackdbus-detect, Pulseaudio JACK Sink/Source connections are automatically loaded when JACK starts
I have seen a few Cadence users turn on the Pulseaudio bridge option without noticing that connections are already loaded and create a second pair of Pulseaudio connections
in QjackCtl just need to turn on 2 settings to use D-Bus, Pulseaudio JACK Sink/Source connections are automatically loaded
if using D-Bus is not possible or preferable, Pulseaudio sinks and sources can be loaded by simple terminal commands
This can be configured to run automatically in QjackCtl using option to run script after JACK started
QjackCtl option to run script after JACK started can also be used for connections to ALSA loopbacks
Not recommended to run both ALSA and Pulseaudio connections
Re: qjackctl with "JACK Bridges"
So, in this case, the JACK bridge is unnecessary?
People should carry on useing these fat burners now especially.
- nikgnomicradio
- Established Member
- Posts: 109
- Joined: Wed Feb 07, 2018 9:31 pm
- Has thanked: 1 time
- Been thanked: 7 times
- Contact:
Re: qjackctl with "JACK Bridges"
Pulseaudio JACK connections can launch automatically with D-Bus when JACK starts
If so, Cadence option to load Pulseaudio JACK connections may not be needed, unless 2nd pair of connections is wanted
If not using D-Bus, Pulseaudio connections can be created after JACK is started with commands:
If so, Cadence option to load Pulseaudio JACK connections may not be needed, unless 2nd pair of connections is wanted
If not using D-Bus, Pulseaudio connections can be created after JACK is started with commands:
Code: Select all
pactl load-module module-jack-sink
pactl load-module module-jack-source