Impulse convolver/guitarix

Programming applications for making music on Linux.

Moderators: khz, MattKingUSA

Re: Impulse convolver/guitarix

Postby brummer » Sat Jun 19, 2010 3:51 pm

I see in the picture that you have enabled the experimental switch, have you try it without the experimental flag enabled ?
Do you get this behaviour with all presets ?
I mean it's strange anyway, I will start a measure session, to find out what's going on.
brummer
 

Re: Impulse convolver/guitarix

Postby brummer » Sat Jun 19, 2010 4:02 pm

could you send me the preset were you get the most notable delay ?
brummer
 

Re: Impulse convolver/guitarix

Postby AutoStatic » Sat Jun 19, 2010 4:03 pm

Sure! But I wasn't using the experimental preamp, or does the experimental setting enable an extra stage anyway?
And I'm back on 0.08.0. No lagging.
Here's the relevant preset data:
Code: Select all
"OLP-Bass", {
    "engine": {
      "IR.auto_freq": 0,
      "IR.bandwidth": 100,
      "IR.freq": 440,
      "IR.on_off": 0,
      "IR.peak": 1,
      "IR.position": 4,
      "MultiBandFilter.Q125": 50,
      "MultiBandFilter.Q16k": 50,
      "MultiBandFilter.Q1k": 50,
      "MultiBandFilter.Q250": 50,
      "MultiBandFilter.Q2k": 50,
      "MultiBandFilter.Q31_25": 50,
      "MultiBandFilter.Q4k": 50,
      "MultiBandFilter.Q500": 50,
      "MultiBandFilter.Q62_5": 50,
      "MultiBandFilter.Q8k": 50,
      "MultiBandFilter.f125": 0,
      "MultiBandFilter.f16k": 0,
      "MultiBandFilter.f1k": 0,
      "MultiBandFilter.f250": 0,
      "MultiBandFilter.f2k": 0,
      "MultiBandFilter.f31_25": 0,
      "MultiBandFilter.f4k": 0,
      "MultiBandFilter.f500": 0,
      "MultiBandFilter.f62_5": 0,
      "MultiBandFilter.f8k": 0,
      "MultiBandFilter.on_off": 0,
      "SampleLooper.Capture": 0,
      "SampleLooper.Play": 0,
      "SampleLooper.gain": 0,
      "SampleLooper.on_off": 0,
      "amp.balance": 0,
      "amp.bass_boost.on_off": 0,
      "amp.feedback": 0,
      "amp.feedforward": 0,
      "amp.fuzz": 1,
      "amp.in_level": 0,
      "amp.out_master": -15,
      "amp.oversample.on_off": 0,
      "amp.select": 4,
      "amp.threshold": 0,
      "amp.tonestack.Bass": 0.7,
      "amp.tonestack.Middle": 1,
      "amp.tonestack.Treble": 1,
      "amp.tonestack.select": 0,
      "anti_aliase.feedback": 0.3,
      "anti_aliase.on_off": 0,
      "beat_detector.atack_gain": 5,
      "beat_detector.beat_gain": 1,
      "beat_detector.midi_gain": 1,
      "beat_detector.note_off": 2,
      "beat_detector.stepper": 1,
      "biquad.Freq": 1200,
      "biquad.on_off": 1065353216,
      "cab.on_off": 0,
      "chorus.delay": 0.025,
      "chorus.depth": 0.02,
      "chorus.freq": 3,
      "chorus.level": 0.5,
      "chorus.on_off": 0,
      "chorus.position": 7,
      "compressor.attack": 0.002,
      "compressor.knee": 3,
      "compressor.on_off": 0,
      "compressor.position": 0,
      "compressor.ratio": 15.5609,
      "compressor.release": 0.5,
      "compressor.threshold": -20,
      "convolve.on_off": 1065353216,
      "convolve.select": 0,
      "crybaby.autowah": 0,
      "crybaby.level": 0.1,
      "crybaby.on_off": 0,
      "crybaby.position": 5,
      "crybaby.wah": 0,
      "crybaby.wet_dry": 0,
      "delay.delay": 0,
      "delay.gain": 0,
      "delay.on_off": 0,
      "delay.position": 8,
      "distortion.drive": 0.18,
      "distortion.gain": 2,
      "distortion.high_drive": 1,
      "distortion.high_gain": 10,
      "distortion.level": 0.01,
      "distortion.low_drive": 1,
      "distortion.low_gain": 10,
      "distortion.low_highcutoff.high_freq": 5000,
      "distortion.low_highcutoff.low_freq": 130,
      "distortion.low_highcutoff.on_off": 0,
      "distortion.low_highpass.high_freq": 130,
      "distortion.low_highpass.low_freq": 5000,
      "distortion.low_highpass.on_off": 0,
      "distortion.middle_drive": 1,
      "distortion.middle_gain": 10,
      "distortion.on_off": 0,
      "distortion.position": 1,
      "distortion.resonator.on_off": 0,
      "distortion.split_high_freq": 650,
      "distortion.split_low_freq": 250,
      "distortion.trigger": 0.12,
      "distortion.vibrato": 1,
      "distortion1.drive": 0.64,
      "distortion1.gain": 2,
      "distortion1.level": 0.01,
      "distortion1.low_highcutoff.high_freq": 5000,
      "distortion1.low_highcutoff.low_freq": 130,
      "distortion1.low_highcutoff.on_off": 0,
      "distortion1.low_highpass.high_freq": 130,
      "distortion1.low_highpass.low_freq": 5000,
      "distortion1.low_highpass.on_off": 0,
      "distortion1.resonator.on_off": 0,
      "distortion1.trigger": 0.12,
      "distortion1.vibrato": 1,
      "distortiont.onetwo": 0,
      "drive.on_off": 0,
      "drive.value": 8,
      "echo.on_off": 0,
      "echo.percent": 0,
      "echo.position": 6,
      "echo.time": 1,
      "eq.Q125": 50,
      "eq.Q16k": 50,
      "eq.Q1k": 50,
      "eq.Q250": 50,
      "eq.Q2k": 50,
      "eq.Q31_25": 50,
      "eq.Q4k": 50,
      "eq.Q500": 50,
      "eq.Q62_5": 50,
      "eq.Q8k": 50,
      "eq.f125": 0,
      "eq.f16k": 0,
      "eq.f1k": 0,
      "eq.f250": 0,
      "eq.f2k": 0,
      "eq.f31_25": 0,
      "eq.f4k": 0,
      "eq.f500": 0,
      "eq.f62_5": 0,
      "eq.f8k": 0,
      "eq.on_off": 0,
      "eqs.Qs125": 50,
      "eqs.Qs16k": 50,
      "eqs.Qs1k": 50,
      "eqs.Qs250": 50,
      "eqs.Qs2k": 50,
      "eqs.Qs31_25": 50,
      "eqs.Qs4k": 50,
      "eqs.Qs500": 50,
      "eqs.Qs62_5": 50,
      "eqs.Qs8k": 50,
      "eqs.freq125": 125,
      "eqs.freq16k": 16000,
      "eqs.freq1k": 1000,
      "eqs.freq250": 250,
      "eqs.freq2k": 2000,
      "eqs.freq31_25": 31,
      "eqs.freq4k": 4000,
      "eqs.freq500": 500,
      "eqs.freq62_5": 62,
      "eqs.freq8k": 8000,
      "eqs.fs125": 0,
      "eqs.fs16k": 0,
      "eqs.fs1k": 0,
      "eqs.fs250": 0,
      "eqs.fs2k": 0,
      "eqs.fs31_25": 0,
      "eqs.fs4k": 0,
      "eqs.fs500": 0,
      "eqs.fs62_5": 0,
      "eqs.fs8k": 0,
      "eqt.onetwo": 0,
      "flanger.LFO freq": 0.2,
      "flanger.depth": 1,
      "flanger.feedback gain": 0,
      "flanger.flange delay": 10,
      "flanger.flange delay offset": 1,
      "flanger.invert": 0,
      "flanger.level": 0,
      "flanger.on_off": 0,
      "flanger.position": 8,
      "freeverb.RoomSize": 0.5,
      "freeverb.damp": 0.5,
      "freeverb.on_off": 0,
      "freeverb.position": 2,
      "freeverb.wet_dry": 0,
      "jconv.left_delay": 0,
      "jconv.left_gain": 0,
      "jconv.on_off": 1,
      "jconv.right_delay": 0,
      "jconv.right_gain": 0,
      "jconv.wet_dry": 0,
      "midi_out.channel_1.auto_pitch": 0,
      "midi_out.channel_1.autogain": 0,
      "midi_out.channel_1.channel": 0,
      "midi_out.channel_1.oktave": 0,
      "midi_out.channel_1.program": 0,
      "midi_out.channel_1.sensity": 20,
      "midi_out.channel_1.velocity": 64,
      "midi_out.channel_1.volume": 64,
      "midi_out.channel_2.auto_pitch": 0,
      "midi_out.channel_2.autogain": 0,
      "midi_out.channel_2.channel": 0,
      "midi_out.channel_2.oktave": 0,
      "midi_out.channel_2.on_off": 0,
      "midi_out.channel_2.program": 0,
      "midi_out.channel_2.sensity": 20,
      "midi_out.channel_2.velocity": 64,
      "midi_out.channel_2.volume": 64,
      "midi_out.channel_3.auto_pitch": 0,
      "midi_out.channel_3.autogain": 0,
      "midi_out.channel_3.channel": 0,
      "midi_out.channel_3.oktave": 0,
      "midi_out.channel_3.on_off": 0,
      "midi_out.channel_3.program": 0,
      "midi_out.channel_3.sensity": 20,
      "midi_out.channel_3.velocity": 64,
      "midi_out.channel_3.volume": 64,
      "moog.Q": 1,
      "moog.fr": 3000,
      "moog.on_off": 0,
      "noise_gate.on_off": 0,
      "noise_gate.threshold": 0.21,
      "overdrive.drive": 3.57895,
      "overdrive.on_off": 0,
      "overdrive.position": 3,
      "preamp.atan": 6,
      "preamp.on_off": 0,
      "shaper.on_off": 0,
      "shaper.sharper": 1,
      "test.Pregain": 30,
      "test.highshelf": 0,
      "test.stage1.ON": 0,
      "test.stage1.gain1": 6,
      "test.stage2.ON": 0,
      "test.stage2.gain2": 6,
      "test.stage3.ON": 0,
      "test.stage3.gain3": 6,
      "test.upsample": 0,
      "tube.fuzzy": 2,
      "tube.on_off": 1065353216,
      "tube.vibrato": 0,
      "tube.vibrato.on_off": 0,
      "tube2.fuzzy": 6,
      "tube2.on_off": 0,
      "tube2.resonanz": 0,
      "tube2.vibrato": 0,
      "tube3.dist": 0,
      "tube3.g": 1,
      "tube3.on_off": 0,
      "tube3.q": 0.4
    },
    "jconv": {
      "jconv.IRFile": "Ampeg_8x10_D6_AH.wav",
      "jconv.IRDir": "/home/music/Guitarix/IR",
      "jconv.Gain": 0.2,
      "jconv.lGain": 0.2,
      "jconv.Mem": 24320,
      "jconv.Mode": 0,
      "jconv.BufferSize": 64,
      "jconv.Offset": 0,
      "jconv.Length": 0,
      "jconv.Delay": 0,
      "jconv.lDelay": 0
    }
  }
User avatar
AutoStatic
Establlshed Member
 
Posts: 1447
Joined: Wed Dec 09, 2009 5:26 pm
Location: Beverwijk, The Netherlands

Re: Impulse convolver/guitarix

Postby brummer » Sat Jun 19, 2010 7:18 pm

So, I have made some measure's with both versions, and couldn't found a diff in terms of time and sample duration, . . ?
I see in the screenshot a jack_buffer_size from 1024 samples, in your preset you use 64 samples, could it be that you run the test with different frames/periode settings then you normal use ?
brummer
 

Re: Impulse convolver/guitarix

Postby AutoStatic » Sat Jun 19, 2010 7:39 pm

Hello brummer, I made the screenshot on a different machine than the machine I normally work on. I'll try compiling 0.09.0 without the experimental stuff and report back.
The setup is like this: sequencer (Hydrogen) with bass sample --> guitarix --> Qtractor
The slight lagging is audible at the beginning of the loop/pattern so it could be a Hydrogen timing issue too. But that doesn't explain why it works with 0.08.0.
User avatar
AutoStatic
Establlshed Member
 
Posts: 1447
Joined: Wed Dec 09, 2009 5:26 pm
Location: Beverwijk, The Netherlands

Re: Impulse convolver/guitarix

Postby morko » Sun Jun 20, 2010 7:40 am

Hi.

I tried to build with optimization flag and it failed.

Code: Select all
Waf: Entering directory `/tmp/packerbuild-1000/guitarix/guitarix/src/guitarix-0.09.0/build'
[ 1/43] cxx: ladspa/crybaby.cpp -> build/default/ladspa/crybaby_1.o
[ 2/43] cxx: ladspa/distortion.cpp -> build/default/ladspa/distortion_2.o
../ladspa/crybaby.cpp:1:0: virhe: bad value (K8) for -march= switch
../ladspa/distortion.cpp:1:0: virhe: bad value (K8) for -march= switch
Waf: Leaving directory `/tmp/packerbuild-1000/guitarix/guitarix/src/guitarix-0.09.0/build'
Build failed
 -> task failed (err #1):
   {task: cxx crybaby.cpp -> crybaby_1.o}
 -> task failed (err #1):
   {task: cxx distortion.cpp -> distortion_2.o}
==> ERROR: Build Failed.
morko
Establlshed Member
 
Posts: 45
Joined: Thu Mar 25, 2010 8:08 am
Location: Finland

Re: Impulse convolver/guitarix

Postby adegert » Sun Jun 20, 2010 9:45 am

AutoStatic wrote:The fx loop introduces extra latency so now my recorded loops/samples that I run through guitarix are lagging :(


I don't think its Guitarix. You can use jdelay to measure the latency: check out and compile the newest svn version, then switch off all processing (especially tonestack = "Off", jdelay can only work with a clean channel without filtering or distortion) and connect the jdelay ports to input and output of Guitarix (jdelay:out -> guitarix_amp -> guitarix_fx -> jdelay:in). jdelay should report a latency equal to your current jack buffer size.

Switching on oversampling of the amp section (but without any further processing) should add 32 samples latency (that's 0.7ms at a sample rate of 44100).

Off course any filter introduces a phase delay, but I don't think that's what you describe as "lag" (how much lag do you see, in samples?)

ciao
Andreas
adegert
Establlshed Member
 
Posts: 10
Joined: Sun Feb 21, 2010 12:45 pm

Re: Impulse convolver/guitarix

Postby adegert » Sun Jun 20, 2010 9:51 am

morko wrote:Hi.

I tried to build with optimization flag and it failed.

Code: Select all
../ladspa/crybaby.cpp:1:0: virhe: bad value (K8) for -march= switch


does it work when you change -march=K8 to -march=k8 (lowercase k) in trunk/wscript?
adegert
Establlshed Member
 
Posts: 10
Joined: Sun Feb 21, 2010 12:45 pm

Re: Impulse convolver/guitarix

Postby AutoStatic » Sun Jun 20, 2010 10:39 am

adegert wrote:
AutoStatic wrote:The fx loop introduces extra latency so now my recorded loops/samples that I run through guitarix are lagging :(


I don't think its Guitarix. You can use jdelay to measure the latency: check out and compile the newest svn version, then switch off all processing (especially tonestack = "Off", jdelay can only work with a clean channel without filtering or distortion) and connect the jdelay ports to input and output of Guitarix (jdelay:out -> guitarix_amp -> guitarix_fx -> jdelay:in). jdelay should report a latency equal to your current jack buffer size.

Switching on oversampling of the amp section (but without any further processing) should add 32 samples latency (that's 0.7ms at a sample rate of 44100).

Off course any filter introduces a phase delay, but I don't think that's what you describe as "lag" (how much lag do you see, in samples?)

ciao
Andreas
Hello Andreas, I jumped to the wrong conclusions and already figured out that it's not the FX loop that causes the lagging. It must be something else, I'll reinstall 0.09.0 svn 743 and give it a testride again with jdelay. What about the Experimental part of guitarix, does that introduce an extra stage/latency? Otherwise I should try compiling a version without the experimental switch.
User avatar
AutoStatic
Establlshed Member
 
Posts: 1447
Joined: Wed Dec 09, 2009 5:26 pm
Location: Beverwijk, The Netherlands

Re: Impulse convolver/guitarix

Postby adegert » Sun Jun 20, 2010 11:04 am

AutoStatic wrote:I'll reinstall 0.09.0 svn 743 and give it a testride again with jdelay. What about the Experimental part of guitarix, does that introduce an extra stage/latency? Otherwise I should try compiling a version without the experimental switch.


No it shouldn't, and anyhow there is a switch to activate (or deactivate) it (open the experimental window from the engine menu and check the switches; and maybe just activate it because it sounds good ;-).

For jdelay you'd have to use svn 744, that's the version where I added "Off" to the tonestack.

ciao
Andreas
adegert
Establlshed Member
 
Posts: 10
Joined: Sun Feb 21, 2010 12:45 pm

Re: Impulse convolver/guitarix

Postby AutoStatic » Mon Jun 21, 2010 7:26 pm

Ok, now using svn 746 and all is well, no more lagging and a good sound. Thanks guys!
User avatar
AutoStatic
Establlshed Member
 
Posts: 1447
Joined: Wed Dec 09, 2009 5:26 pm
Location: Beverwijk, The Netherlands

Re: Impulse convolver/guitarix

Postby brummer » Mon Jun 21, 2010 7:58 pm

Good to hear :)
AutoStatic, I have move the link for ubuntu karmic binary's , on the guitarix project-page, form pillips to your ppa, hope that is well for you.
brummer
 

Re: Impulse convolver/guitarix

Postby AutoStatic » Mon Jun 21, 2010 8:56 pm

Hello brummer, that' s ok!
And I can load presets now with the help of the -f option, was it there before?
User avatar
AutoStatic
Establlshed Member
 
Posts: 1447
Joined: Wed Dec 09, 2009 5:26 pm
Location: Beverwijk, The Netherlands

Re: Impulse convolver/guitarix

Postby brummer » Wed Jun 23, 2010 6:02 pm

Yes, it's included since 0.08.0, but you cant really load a presetfile with it, you can load a state file, that means a main settings file, guitarix_rc (now guitarix_amp_rc), witch contain a bit more info (GUI settings, . . ) then the presetfiles, so you need to save your preset as "main settings" and rename the resulting file guitarix_amp_rc to your needs to get it permanent. Then you could load it at startup with the -f option.
I have completely forget this option. :)
brummer
 

Re: Impulse convolver/guitarix

Postby funkmuscle » Wed Jun 23, 2010 7:46 pm

Updated to revision 750

./waf build
Waf: Entering directory `/home/harv/audio/guitarix/build'
Waf: Leaving directory `/home/harv/audio/guitarix/build'
source not found: 'gxwidgets-module.c' in 'dir:///home/harv/audio/guitarix/lib'
funkmuscle
Establlshed Member
 
Posts: 1155
Joined: Mon Jun 02, 2008 2:30 pm

PreviousNext

Return to Developer's Section

Who is online

Users browsing this forum: No registered users and 0 guests